Need help to config my TDM400P
Submitted by malbep on Fri, 08/15/2008 - 6:02am.
Hey every one,
I need help with my TDM400P, it were working fine with trixbox 2.4 and when I ugrade to 2.6.1, it not working anymore. I have the green led in the card but when you type on CLI: ztcfg -vv: you have the output saying
channel 01: FXO Kewlstart (Default) (Slaves: 01)
channel 02: FXS Kewlstart (Default) (Slaves: 02)
2 channels to configure
Any help on our to configure this channels pls, I don't have enough experience on linux command if you can be more detail or specific, I will appreciate that.
Again thank in advance for your help
I have the same problem
i
Sun, 09/07/2008 - 9:35am
I have the same problem
i run setup-pstn and then i run ztcfg -vv and i get that same channel map saying that i have 2 channels to configure.
Channel 01: FXO Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
2 Channels to configure.
Any ideas?
Zapata-auto.conf
; Autogenerated by /usr/sbin/genzaptelconf -- do not hand edit
; Zaptel Channels Configurations (zapata.conf)
;
; This is not intended to be a complete zapata.conf. Rather, it is intended
; to be #include-d by /etc/zapata.conf that will include the global settings
;
; Span 1: WCTDM/0 "Wildcard TDM400P REV E/F Board 1" (MASTER)
;;; line="1 WCTDM/0/0"
signalling=fxo_ks
callerid="Channel 1" <6001>
mailbox=6001
group=5
context=from-internal
channel => 1
callerid=
mailbox=
group=
context=default
;;; line="2 WCTDM/0/1"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 2
context=default
Zapata.conf
;
; Zapata telephony interface
;
; Configuration file
[trunkgroups]
[channels]
language=en
context=from-zaptel
signalling=fxs_ks
rxwink=300 ; Atlas seems to use long (250ms) winks
;
; Whether or not to do distinctive ring detection on FXO lines
;
;usedistinctiveringdetection=yes
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=no
;echotraining=800
rxgain=0.0
txgain=0.0
group=0
callgroup=1
pickupgroup=1
immediate=no
;faxdetect=both
faxdetect=incoming
;faxdetect=outgoing
;faxdetect=no
;Include genzaptelconf configs
#include zapata-auto.conf
group=1
;Include AMP configs
#include zapata_additional.conf
zapata_addtional.conf
; do not edit this file, this is an auto-generated file by freepbx
; all modifications must be done from the web gui
;;;;;;[205]
signalling=fxo_ks
record_out=Adhoc
record_in=Adhoc
mailbox=205@device
immediate=no
echotraining=800
echocancelwhenbridged=no
echocancel=yes
dial=ZAP/1
context=from-internal
callprogress=no
callerid=device <205>
busydetect=no
busycount=7
accountcode=
channel=>1
;;;;;;[205]
signalling=fxo_ks
record_out=Adhoc
record_in=Adhoc
mailbox=205@device
immediate=no
echotraining=800
echocancelwhenbridged=no
echocancel=yes
dial=ZAP/1
context=from-internal
callprogress=no
callerid=device <205>
busydetect=no
busycount=7
accountcode=
channel=>2
Member Since:
2008-03-15